Pirate Brand, S-Series, DUAL-CHAMBER Series - 8 CU FT., DOUBLE OUTLET, STANDARD MODEL - Blast Pot, STATIONARY, 12VDC Electric Controls

Pirate Brand, S-Series, DUAL-CHAMBER Series - 8 CU FT., DOUBLE OUTLET, STANDARD MODEL - Blast Pot, STATIONARY, 12VDC Electric Controls

Manufacturer: Pirate Brand

Part Number: 888-0642-33940PB-E

IMPORTANT! NEVER REVERSE POLARITY ON THE DUAL-CHAMBER CONTROL BOX POWER SUPPLY.  REVERSING POLARITY CAN CAUSE THE DUAL-CHAMBER CYCLE TO MALFUNCTION.  SEE INCLUDED WIRING DIAGRAM WHEN REPLACING POWER CORD OR WIRING TO A POWER SOURCE.

A 12VDC POWER SUPPLY IS REQUIRED FOR ALL 8.0 CU FT DUAL CHAMBER BLASTERS WITH PNEUMATIC OR ELECTRIC CONTROLS.

Description: BLAST POT, STATIONARY, 8.0 CU. FT, 2 OUTLET, DUAL-CHAMBER, ELECTRIC

Includes:

• (2) Electric Control Handles
• (2) 110' Control Cord
• (2) MPV Metering Valves

Product Highlights:

A. 8.0 CU. FT. CAPACITY (225 LITERS)
      1. UPPER CHAMBER - 3.25 CU FT (2.69 USEABLE) LOWER CHAMBER - 4.19 CU FT (4.04 USEABLE)
      2. 150 PSI VESSEL (10.3 BAR)
      3. A.S.M.E. SECTION VIII DIVISION 1
      4. CRN FOR ALL PROVINCES
B. DUAL-CHAMBER SYSTEM
      1. CONTINUOUSLY REFILLS WHILE REMAINING PRESSURIZED
      2. INCREASES PRODUCTIVITY BY ELIMINATING THE NEED TO STOP BLASTING WHILE REFILLING
C. BIG GUN FULL FLOW SYSTEMS PROVIDES
      1. A ZERO PRESSURE DROP PATH FOR AIR & ABRASIVE TO TRAVEL TO THE BLAST NOZZLE. EVERY 1 PSI GAINED OR LOST IN ABRASIVE BLASTING = 1.5% PRODUCTION
      2. A MUST FOR #7 & #8 NOZZLES
      3. FULL PORT COUPLING BLAST HOSE CONNECTION PROVIDES AN UNRESTRICTED PATH FOR AIR & ABRASIVE TO TRAVEL TO THE NOZZLE
D. ELECTRIC CONTROLS 12VDC
      1. WHEN RUNNING OVER 100 FEET OF BLAST HOSE THIS ADDS ADDITIONAL SPEED TO STOPPING & STARTING THE BLASTING OPERATION
      2. HELPS WITH FREEZING PROBLEMS IN COLD WEATHER
      3. HEAvY DUTY FILTERED CONTROL VALVE REDUCES STOPPING TIME WHEN CONTROL HANDLE IS RELEASED
E. DUAL-CHAMBER CYCLE CONTROLS HOUSED IN A NEMA 4 RATED ENCLOSURE
F. GALVANIZED PIPING FOR CORROSION RESISTANCE
      1. 1-1/2" PIPING
      2. 2" INLET
G. HEAVY DUTY FULL PORT BALL VALVES
H. EXTENDED LIFE SCHEDULE 80 HEAVY DUTY NIPPLE
      1. WITHSTANDS ABRASIVE WEAR FOR LONGER LIFE
I. BOLT CLAMPS ON PUSHER LINE MAKE FIELD REPAIRS EASIER
J. COMBINATION VALVE/APVII VALVE
      1. COMBINATION VALVE IS A 2 IN 1 DESIGN THAT IS RESPONSIBLE FOR CYCLING THE TOP CHAMBER IN DUAL-CHAMBER SYSTEMS
      2. AUTOMATIC PLUNGER VALVE II (APVII) PREMIUM ABRASIVE METERING VALVE WITH QUADRUPLE PLUNGER SEAL ARRANGEMENT SOLVES THE AIR & ABRASIVE CARRY OVER PROBLEM AS WELL AS THE PLUNGER & SEAL JAMMING PROBLEM NORMALLY ASSOCIATED WITH REGULATED LOW PRESSURE BLASTING APPLICATIONS AND OR THE USE OF STEEL ABRASIVE. SOLID MACHINED TUNGSTEN CARBIDE PLUNGER & SLEEVE PROVIDES FAR SUPERIOR WEAR RATES AND 100% CONSISTENT TOLERANCES. 1" NPT CLEANOUT PORT GIVES ACCESS TO OBSTRUCTIONS THAT MAY BE BRIDGING OVER THE METERING PORT ALSO ALLOWS YOU TO DRAIN THE VESSEL WITHOUT REMOVING THE VALVE.     
K. 15' BLOWDOWN HOSE ASSEMBLY FOR REMOTE MOUNTING
L. 9" ADJUSTABLE SPIDER
      1. FULLY ADJUSTABLE FOR DIFFERENT MEDIA TYPES & SIZES
      2. WHEN ABRASIVE IS HOPPER FEED FROM ABOVE THIS KEEPS THE WEIGHT OF THE ABRASIVE OFF THE POP-UP ALLOWING IT TO CLOSE & SEAL PROPERLY
M. SKIRTED POP-UP GASKET
      1. SKIRTED POP-UP GASKET BY DESIGN WILL KNIFE ITS WAY THROUGH THE ABRASIVE TO ASSIST IN SEALING
      2. HELPS WITH THE ABRASIVE BURPING PROBLEM THAT IS COMMONLY SEEN WITH HOPPER FEED BLAST POTS
      3. A MUST WHEN USING LARGE GRIT SIZES
N. UNION END BALL VALVES
      1. ALLOWS YOU TO SHUT OFF THE ABRASIVE AT THE BOTTOM OF THE POT FOR MAINTENANCE/REPAIRS AND REMOVE THE ABRASIVE METERING VALVE WITHOUT DUMPING THE ENTIRE VESSEL OF ABRASIVE ON THE FLOOR
0. FULL LOAD LIFTING EYES
      1. ALLOW LIFTING AND TRANSPORTATION OF VESSEL FOR PLACEMENT MAINTENANCE OR REPAIR