website

Aftermarket Graco® Fine Finish AAF Tips (Non-OEM)

$85.00

Aftermarket Graco® Fine Finish AAM Tips (Non-OEM) for G15 and G40 Spray Guns

Manufacturer: Total Finishing Supplies

Part Number: 190833xxx 

Comparable OEM Part Number:  63-611-XXX

Description: Aftermarket Graco® Fine Finish AAM Tips (Non-OEM). AAM tips for G15 and G40 spray guns

Comparable to Graco® 63-611-XXX

These aftermarket Graco® non-OEM air-assisted airless pin spray tips are used with air-assisted airless gun models G15™, G40™, Silver Plus™, and Mini Merkur. With our wide selection of Aftermarket non-OEM Graco® sprayer tips, you will achieve a soft spray atomization in various spray patterns and orifice combinations when the proper paint filters are used. Whether you require our standard or fine finish pre-atomizer versions for your air-assisted sprayer, you can find the right paint spray tips to solve all your fluid dynamics requirements.

By administering a small amount of air to aid in completing the pattern formation, you are able to attain the fine finish results required while greatly reducing excessive bounce back. Applying the spray coating at significantly lower pressures than a normal airless setup, your air-assisted airless spray equipment will undergo less wear and tear. This resulting in less maintenance and clean up of your air-assisted airless spray equipment allowing it to last longer.

NOTES:

Graco®, PerfomAA™, Merkur™  and Reverse-A-Clean® (RAC) Tip are registered trademarks of Graco®, and the same company may claim unregistered trademark rights in other words. The advertised parts are intended to fit Graco®, PerfomAA™, Merkur™ and Reverse-A-Clean® (RAC) Tip spray equipment. They are not, however, manufactured, endorsed, or sponsored by Graco® or any of their affiliates, and no warranty by Graco®, or any of their affiliates applies. Total Finishing Solutions, LLC is not affiliated with or sponsored or endorsed by Graco® and is not one of their authorized distributors.


** Minimum Order $25 to qualify for Free Shipping

Tip Size Degree Orifice Size Fan Pattern OEM Part Number
208 20 0.008 4-6 inches 63-611-107
210 20 0.010 4-6 inches 63-611-109
212 20 0.012 4-6 inches 63-611-111
308 30 0.008 6-8 inches 63-611-207
310 30 0.010 6-8 inches 63-611-209
312 30 0.012 6-8 inches 63-611-211
408 40 0.008 8-10 inches 63-611-213
410 40 0.010 8-10 inches 63-611-215
412 40 0.012 8-10 inches 63-611-217
414 40 0.014 8-10 inches 63-611-219
416 40 0.016 8-10 inches 63-611-221
510 50 0.010 10-12 inches 63-611-307
512 50 0.012 10-12 inches 63-611-309
514 50 0.014 10-12 inches 63-611-311
516 50 0.016 10-12 inches 63-611-313
610 60 0.010 12-14 inches 63-611-315
612 60 0.012 12-14 inches 63-611-317
614 60 0.014 12-14 inches 63-611-319
616 60 0.016 12-14 inches 63-611-321
712 70 0.012 14-16 inches 63-611-409
714 70 0.014 14-16 inches 63-611-411
716 70 0.016 14-16 inches 63-611-413